ONX4.80/500
6
5 Channel Discrete Operation:
MODE: “5” since 3 sets of RCA’s are connected.
You can use this configuration simply as 4 discrete full range channels, with a 5th low
pass channel. All of the crossovers are bypassed , except the LOW PASS on channel 5.
Control checklist:
- Refer to the section “Settings for Best Performance”
Interconnect cable checklist:
Connect channel 1&2 inputs to the front output, channels 3&4 to the rear output, and
Minimum final loudspeaker impedances:
channel 5 to the mono subwoofer output of a head unit or in dash equalizer.
- 2 Ohms per channel for channels 1-4
- 1 Ohm on channel 5
Switch setting checklist:
- CH 1 / 2 X-OVER: FULL
- CH 3 / 4 X-OVER: FULL
Single Set of Stereo RCA’s
MODE: “2” since 1 set of RCA’s are connected.
We will use the same basic setup on the speaker and subwoofer connections as above
to illustrate an installation that only has 1 set of stereo RCA’s to connect to this amplifier.
Control checklist:
By switching the amplifier to 2CH on the INPUT MODE, you now provide signal to all
- Refer to the section “Settings for Best Performance”
channels on the amplifier. You sacrifice the ability to fade front to rear though.
Minimum final loudspeaker impedances:
Interconnect cable checklist:
- 2 Ohms per channel for channels 1-4
Connect Stereo Left and Right RCA’s from headunit to CH1&2 RCA Inputs.
- 1 Ohm on channel 5
Switch setting checklist:
- CH 1 / 2 X-OVER: FULL
- CH 3 / 4 X-OVER: FULL
5-Channel Amplifiers
FEATURES:
- 3 Sets of RCA inputs
- LEVEL: Variable sensitivity from 0.2V to 6V
- BASS EQ: Adjustable 45Hz bass boost from 0dB to 10dB
- X-OVER: Selects internal crossover functions
- FULL: Bypasses all crossovers for full frequency operation
- BP: Selects the built in LOW PASS filter, variable from 30Hz to 150Hz
- HI: Selects the built in HI PASS filter, variable from 10Hz to 15KHz
- POWER LED: Indicates the powered up and turned on condition
- PROTECTION LED: Indicates a high voltage, low voltage, short circuit,
hard clip, over heating or DC fault condition.
- MODE: “2” indicates one set of RCA’s are being used. This will also pass signal to channels 3/4 and 5 through
1/2 inputs. “4” indicates connecting 2 sets of RCA’s to 1/2 and 3/4 inputs. “5” indicates connecting 3 sets of
RCA’s to channels 1/2, 3/4 and mono signal to channel 5 inputs.
REMOTE
POWER
PROTECT
LINE INPUT
CH2
CH1
CH4
CH3
5CH
10Hz 15Khz
10Hz 15Khz
HI PASS
6V 0.2V
LEVEL
6V 0.2V
LEVEL
LOW PASS
30Hz 150Hz
HI PASS
MODE
Ch2 Ch4 Ch5
X-OVER
CH3/4
0dB-10dB
30Hz 150Hz
6V 0.2V
BASS EQ
LOW PASS LEVEL
HI FULL
HI FULL BP
X-OVER
CH1/2
POWER INPUT
GND REM BATT+12V
1CH 2CH 3CH 4CH 5CH
+ - + - + - + - + -
BRIDGED BRIDGED
ONYX
REMOTE
POWER
PROTECT
LINE INPUT
CH2
CH1
CH4
CH3
5CH
10Hz 15Khz
10Hz 15Khz
HI PASS
6V 0.2V
LEVEL
6V 0.2V
LEVEL
LOW PASS
30Hz 150Hz
HI PASS
MODE
Ch2 Ch4 Ch5
X-OVER
CH3/4
0dB-10dB
30Hz 150Hz
6V 0.2V
BASS EQ
LOW PASS LEVEL
HI FULL
HI FULL BP
X-OVER
CH1/2
POWER INPUT
GND REM BATT+12V
1CH 2CH 3CH 4CH 5CH
+ - + - + - + - + -
BRIDGED BRIDGED
ONYX
REMOTE
PROTECT
POWER
LINE INPUT
CH2
CH1
CH4
CH3
5CH
10Hz 15Khz
10Hz 15Khz
HI PASS
6V 0.2V
LEVEL
6V 0.2V
LEVEL
LOW PASS
30Hz 150Hz
HI PASS
MODE
Ch2 Ch4 Ch5
X-OVER
CH3/4
0dB-10dB
30Hz 150Hz
6V 0.2V
BASS EQ
LOW PASS LEVEL
HI FULL
HI FULL BP
X-OVER
CH1/2
(88 pages)
(14 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals